CultiKit is a complete micro-growing system with low power consumption, designed for installation under shelves and cabinets, or for integration into bookcases and cupboards. The only limit is your imagination.
Congratulations on your purchase of CultiKit. You are now part of a large community that cares about fresh ingredients and personal health. With your new CultiKit, a world of possibilities opens up in plant cultivation.
Your CultiKit contains the following:
Please read all instructions and precautions before installing and operating your CultiKit.
It is the owners responsibility to ensure that users of the system are aware of all warnings and precautions. When using electrical units, basic precautions must always be followed (including the following).
DANGER – To reduce the risk of electric shock:
WARNING – To reduce the risk of burns, fire, electric shock, or injury:
Additional Precautions
Note: This equipment has been tested and found to comply with the limits for CE, RoHS, EMC and RED standards. These are designed to provide reasonable protection against harmful interference in residential installations.
Controllers, LED panels and fans can both be installed under cupboards and shelves, as well as inside cupboards, drawers and the like. They can be mounted both horizontally and vertically. It does not necessarily have to be kitchen elements you install CultiKit in. Virtually all types of shelves and cabinets are suitable for installation. It is of course also possible to build your own furniture for the plants.
The controller can be attached with the supplied screws which must be placed with 5 cm spacing to fit keyholes. Strong adhesive tape can also be used.
Fans kan be attached with the supplied screws, adhesive tape or strips. In open setups it is a good idea to place them above or to the side of the plant.
LED panels can be attached with the supplied screws and 10 cm distance to fit keyholes. It is also possible to use rope hangers fixed in the keyholes.
It is possible to install CultiKit in closed setups (inside cabinet or tent) by installing a blower fan and connecting it to fan port 1. Fan for wind simulation can be connected to port 2 (If you are using a hydro- or aeroponic system, the fan and water pump can run on the same on/off interval). Check out video guides for inspiration.
LED lights and cables can be hidden behind a list, frame or similar when you install the system. It is also a good idea to use rails or similar to hide cables.
Fans kan be attached with the supplied screws, adhesive tape or strips. Place them above, to the side or below the plants. Use fan covers for safety.
LED panels that are mounted vertically should either run at a maximum of 50% strength, or be shielded to ensure that the light does not disturb.
1Connect cables to LED panels and the LED ports on the controller with the supplied cables.
2Connect PWM fans to the connector and Fan/pump 1 port. Use PWM splitter cables for multiple fans.
3Connect DC accessories to the 2-pin connector and Fan/pump 2 port. Use splitter cables for multiple devices.
4
Plug in the controller with the power supply, and let the magic begin!
Connect the controller at the time you want it to start every day or download CultiApp for maximum control.
LED ports:
12-hour on/off cycle with 30-minute up and down dimming. Preset to 50% light power.
Fan/pump port 1:
24-hour cycle with 5-second on and 25-second off loop. Preset to 80% fan power.
Fan/pump port 2:
24-hour cycle with 1-minute on and 5-minute off loop. Preset to 100% power.
1 click – Toggle status light on/off.
2 click – Change LED power to 100%.
3 click – Change LED to 18 hours on 6 hours off.
Hold 6 sec – Reset controller (all functions and on/off timing).
CultiApp makes it easy to take full control of your system. Simple installation and user-friendly instructions guide you through the setup, allowing you to quickly customize lighting, ventilation, and watering exactly as you want.
Once you have downloaded the app, you just power on the controller and open the app. It will help you access your wifi and set up all the settings, so that in the future you have full control over your system including access to updates and App Support.
It is important to ensure that equipment and surroundings are kept clean when growing plants indoors.
It is the owners responsibility to ensure that users of the system are aware of problems that can arise if the system is not maintained. CultiKit is available with different types of accessories (pots/grow systems, fans, etc.) – please read the following based on the setup you have:
It is important to ensure that equipment and surroundings are kept clean when growing plants indoors.
Controller not turning on
Light(s) not turning on
Fan/pump(s) not turning on
Controller button is not working
Unable to access CultiApp
Culti ApS extends the following Limited Warranty, which applies only to non-commercial indoor use of CultiKit. Any other use of the CultiKit shall void this Limited Warranty. During the applicable Limited Warranty periods described below, the covered components of CultiKit will be free of defects or malfunctions during normal use. Certain exclusions apply, as further described in this Limited Warranty. The Limited Warranty applies for the following components of the CultiKit only, for the time period indicated. The Limited Warranty applies only against defects discovered within the applicable Limited Warranty period and only so long as CultiKit remains in the possession of the original purchaser, or, for gifted CultiKits, the owner of the gifted CultiKit.
CultiKit original components: 24 months
Culti ApS warrants the components and all original parts of the CultiKit (other than 3rd party products) against defects in workmanship and materials for a period of 24 months from the date of original delivery.
Exclusions and Limitations
Who and what is covered:
The original owner of CultiKit. CultiKit must remain in the possession of the original purchaser, or, for gifted CultiKits, the owner of the gifted CultiKit. This Limited Warranty is not transferable. If a defect arises in CultiKit or a warranted component within the applicable Limited Warranty period, the purchaser’s sole and exclusive remedy is for Culti ApS to, at Culti ApS’s discretion to the extent permitted by law, either replace or repair the defective or malfunctioning CultiKit or component with the same or a comparable model. Any replacement or repaired component shall be warranted for the remainder of the original Limited Warranty period or 24 months, whichever is longer, or for any additional period that is required by applicable law.
What is NOT covered:
Any Culti ApS products or services, third party products or labor, units that are, or that Culti ApS reasonably believes to be, stolen, counterfeit, or purchased from an unauthorized distributor or reseller, units purchased or used outside Europe, and units missing the serial numbers.
Software, even if sold with or embedded in the CultiKit, or Internet connectivity. Culti ApS does not warrant that the operation of the CultiKit will be uninterrupted or error-free.
Damage or equipment failure due to normal wear and tear, improper or negligent assembly, maintenance, installation, relocation, or repair (other than that caused by a Culti ApS authorized service technician), use of CultiKit with parts or accessories from third parties that is not sold by Culti ApS, or with parts or accessories not originally intended for or compatible with CultiKit, or any use contrary to the instructions in this manual.
*This limited warranty is the exclusive warranty given by Culti ApS and supersedes any prior, contrary or additional representations. All other warranties, express or implied, including any statutory warranty or condition of merchantability or fitness for a particular purpose, are disclaimed except to the extent prohibited by law. In such event, such warranty is limited to the duration of the warranty periods set forth above. This exclusion applies even if this warranty fails of its essential purposes and regardless of whether damages are sought for breach of warranty, breach of contract, negligence, or strict liability in tort or under any other legal theory. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation may not apply to you. This limited warranty gives you specific legal rights, and you may also have other legal rights, which vary from country to country.
Conformity | CE, RoHS, EMC, RED |
Dimensions | 88x65x22 mm (WxDxH) |
Input Plug Type | Type C |
Input Voltage | 115-240V AC |
Output Voltage | 24V DC |
Output Current | >= 2.5A |
Output Plug | 2.1 mm ID x 5.5 mm OD |
PSU | LED Driver |
Supply Source | 24V DC PSU |
Input Voltage | 24V DC |
Output Voltage | 12V DC ± 5% |
Output Current | >= 1A |
Efficiency | > 50% |
Supported PWM | Most 5-12V fans can be used with the included converter cables. The following third party brands |
Supported DC | Most 5-12V DC 2-pin water and air pumps can be used. It is recommended to use the pumps we supply as accessories with CultiKit so you are sure they have been tested. |
Supply Source | 24V DC PSU |
Input Voltage | 24V DC |
Output Voltage | 3.3V DC ± 5% |
Output Current | >= 1A |
Efficiency | > 50% |
Conformity | CE, RoHS, EMC, RED |
Dimensions | 140x120x10 mm (WxDxH) |
Weight | 116 g |
Power Consumption | 5-18W |
Luminous Efficacy: | 220 lm/W |
Spectrum Range: | 400-700 nm (PAR range) |
Supply Source | 24V DC PSU |
Input Voltage | 24V DC |
Output Voltage | 3.3V DC ± 5% |
Output Current | >= 1A |
Efficiency | > 50% |
This equipment has been tested and certified with SGS certification (CE, RoHS, EMC, RED). These standards provide reasonable protection against harmful interference in a residential installation.
Hereby, Culti ApS declares that the equipment is in compliance with Directive 2014/53/EU. See the full text of the EU declaration of conformity at: www.cultiplantsystems.com/culti-dk/EU-Declaration-of-Conformity.pdf
Manufactured by:
Culti ApS – Kystvejen 4 – 4600 Koege – Denmark – www.cultiplantsystems.com
© Culti ApS 2025 – All rights reserved – MK_230818A V1.0 – MK_230808LED V1.0 – Made in China
How much energy does the system use?
CultiKit is a low voltage system with low energy consumption. The energy consumption depends on how many LED panels, fans and pumps that are connected, how long they run and at what power they run. A controller with 3 LED panels, 2 fans and 1 pump connected at 100% power and runs 12 hours a day uses approx. 30-40W. For comparison, a 42” LED TV uses 70-90W.
If something does not operate as it should, what do I do?
Check as the first troubleshooting here in the guide or check our support and see if you can solve the problem. CultiKit comes with a 2 year warranty so any damage that may happen during shipping or normal wear and tear is covered under the warranty. We will send you replacement parts at no cost to you. Contact support for replacement.
Can I go on vacation and leave my plants?
Yes, as long as you have an irrigation system that supports it you can go on holiday without anyone having to look after your plants.
Are the CultiKit LED lights full spectrum?
Yes, the LED panels consist of efficient Samsung LM301B diodes with a carefully selected mix of 3000K and 5000K LED diodes that ensures a full-spectrum light.
How long does the LED panels last?
Our LED panels and Samsung diodes have a documented lifespan of 50,000 hours. That’s a lot of hours, for example is there 8,765 hours in a year.
Can I adjust the lighting schedule and the lights’ intensity?
Yes, you can easily adjust both on the controller button and with CultiApp. Choose the time of day your lights turn on and at what intensity to balance your plants.
FIll out the form below and we will cantact you as soon as possible